Question
1 studiers recently

Which of the following is true about nodes?

Most modules are connected together in a network to facilitate an increased number of wires.
If the driver depresses the window-down switch, the power window switch sends a window down message to the window node.
Driver’s side window module causes the window to go down.
Each element, also called a node, must communicate with other elements.

Answer

Each element, also called a node, must communicate with other elements.

Was this answer helpful?

Aceify Homework Helper

Get instant answers to any question.

Students also studied these questions

A capacitor used for spike protection will normally be placed in _______ to the load or circuit.
- parallel
A capacitor used for spike protection will normally be placed in _______ to the load or circuit.
- parallel
What will be the total capacitance value in a circuit with capacitors connected in parallel?
- CT = C1 + C 2 + C3…
In a condenser microphone, the _________ is the negatively charged plate of a charged capacitor.
- diaphragm
Identify the insulating material used between two conductive plates in a capacitor.
- Mica
How many charges of electrons is equal to one coulomb?
- 6.25 × 1018 to the eighteenth electrons
A charged capacitor acts like a ________.
- battery
To increase the capacity, what could be done?
- Connect another capacitor in parallel
Capacitors block the flow of ______ current but allow _____current to pass.
- DC; AC
The unit of measurement for capacitor rating is called the _______.
- farad
A capacitor _______________.
- passes alternating current (AC)
What happens to the electrostatic attraction in a condenser microphone if the distance between the plates is reduced?
- The electrostatic attraction between the plates increases.
Capacitors are often used as “suppression capacitors.” What does a capacitor suppress?
- Voltage fluctuations
- Noise
Two technicians are discussing the operation of a capacitor. Technician A says that a capacitor can create electricity. Technician B says that a capacitor can store electricity. Which technician is correct?
- Technician B only
Which of the following statements is true with respect to a Leyden jar?
- A Leyden jar has a capacitor with two conductors and an insulating material.
The relative strength of a material against the flow of electrical current is called __________.
- dielectric constant
___________ of the coil is rapidly released when voltage spike is reduced in a capacitor in parallel connection.
- The energy stored to the magnetic field
__________ are often combined with capacitors to act as electromagnetic interference (EMI) filter circuits for windshield wiper and electric fuel pump motors.
- Radio choke coils
Which of the following is used to reduce radio interference or to improve the performance of a high-power sound system.
- Capacitor
Capacitance can be increased by which one of the following factors?
- Larger surface area of the plates
The relative strength of a material against the flow of electrical current is called __________.
- dielectric constant
Magnetic field strength is measured based on _________.
- ampere-turns
11. Which type of loops are formed by the magnetic field lines?
- Closed
Which of the following rules is used to determine the direction of the magnetic force or thrust on a wire carrying current in a magnetic field?
- Right-hand rule
12. When a conductor cuts across magnetic flux lines, the amount of the voltage depends on _____________.
- magnetic flux lines
Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?
- Both Technicians A and B
The EMF induced in a coil due to the change of flux linked with its own turns is called __________.
- self-induced EMF
Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?
- Both Technicians A and B
The conventional theory for current flow is being used to determine the direction of magnetic lines of force. Technician A says that the left-hand rule should be used. Technician B says that the right-hand rule should be used. Which technician is correct?
- Technician B only
An ignition coil is an example of a _______________.
- step-up transformer
When a conductor is moved to cut magnetic flux lines at an angle of 90 degrees, __________.
- voltage generated will be maximum
An ignition coil operates using the principle(s) of __________________.
- electromagnetic induction
- self-induction
- magnetic Induction
- all of the above
Unlike magnetic poles ____________ and like magnetic poles _______________.
- attract; repel
Technician A says that a relay is an electromagnetic switch. Technician B says that a solenoid uses a movable core. Which technician is correct?
- Both Technicians A and B
Two technicians are discussing electromagnetic induction. Technician A says that the induced voltage can be increased if the speed is increased between the conductor and the magnetic lines of force. Technician B says that the induced voltage can be increased by increasing the strength of the magnetic field. Which technician is correct?
- Both Technicians A and B
Two technicians are discussing ignition coils. Technician A says that some ignition coils have the primary and secondary windings electrically connected. Technician B says that some coils have totally separate primary and secondary windings that are not electrically connected. Which technician is correct?
- Technician B only
The phenomenon due to which there is an induced current in one coil due to the current in a neighboring coil is called _______________.
- mutual inductance
All electronic devices used in vehicles are affected by _________.
- electromagnetic interference
16. As the magnetic flux density increases, the reluctance ________.
- remains the same
The point in a magnet where the intensity of magnetic lines of force is maximum is called ________.
- magnetic pole
A solenoid is an example of which type of switch?
- Electromagnetic
The right-hand rule shows the direction of ____________.
- EMI
- Current flow Electron Theory
- Current Flow Conventional Theory
- Magnetic Flux Lines
Unlike magnetic poles ____________ and like magnetic poles _______________.
- attract; repel
1. On a wiring diagram, S110 with a "0.8 BRN/BLK" means ______.
- c. a splice of a brown with black stripe, wire size being 0.8 mm2 (18 gauge AWG)
12. Capacitors are often used as “suppression capacitors”. What does a capacitor suppress?
- b. Voltage fluctuations
- d. Noise
17. Capacitors block the flow of ______ current but allow _____current to pass.
- c. DC; AC
16. Two technicians are discussing the operation of a capacitor. Technician A says that a capacitor can create electricity. Technician B says that a capacitor can store electricity. Which technician is correct?
- b. Technician B only
15. The unit of measurement for capacitor rating in called the _______.
- c. farad
18. To increase the capacity what could be done?
- b. Connect another capacitor in parallel. X
20. A capacitor used for spike protection will normally be placed in _______ to the load or circuit.
- b. parallel
30. Two technicians are discussing ignition coils. Technician A says that some ignition coils have the primary and secondary windings electrically connected. Technician B says that some coils have totally separate primary and secondary windings that are not electrically connected. Which technician is correct?
- b. Technician B only
22. Unlike magnetic poles ____________ and like magnetic poles _______________.
- b. attract; repel
28. An ignition coil is an example of a _______________.
- c. step-up transformer
21. Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?
- c. Both Technicians A and B
23. The conventional theory for current flow is being used to determine the direction of magnetic lines of force. Technician A says that the left-hand rule should be used. Technician B says that the right-hand rule should be used. Which technician is correct?
- b. Technician B only
24. Technician A says that a relay is an electromagnetic switch. Technician B says that a solenoid uses a movable core. Which technician is correct?
- c. Both Technicians A and B
25. Two technicians are discussing electromagnetic induction. Technician A says that the induced voltage can be increased if the speed is increased between the conductor and the magnetic lines of force. Technician B says that the induced voltage can be increased by increasing the strength of the magnetic field. Which technician is correct?
- c. Both Technicians A and B
2. Where is connector C250?
- b. Under the dash
9. A short circuit can be located using a ____________.
- a. test light
3. All switches illustrated in schematics are ______________.
- a. shown in their normal position
13. Capacitors are commonly used as a___________.
- d. all of the above
14. A charged capacitor acts like a ________.
- b. battery
6. Which relay terminal is the normally closed (N.C.) terminal?
- d. 87a
5. Technician A says that a good relay should measure between 60 and 100 ohms across the coil terminals. Technician B says that OL should be displayed on an ohmmeter when touching terminals 30 and 87. Which technician is correct?
- c. Both Technicians A and B
2. Where is connector C250?
- b. Under the dash
7. Technician A says that there is often more than one circuit being protected by each fuse. Technician B says that more than one circuit often shares a single ground connector. Which technician is correct?
- c. Both Technicians A and B
8. Two technicians are discussing finding a short-to-ground using a test light. Technician A says that the test light, connected in place of the fuse, will light when the circuit that has the short is disconnected. Technician B says that the test light should be connected to the positive (+) and negative terminals of the battery during this test. Which technician is correct?
- a. Technician A only
4. When testing a relay using an ohmmeter, which two terminals should be touched to measure the coil resistance?
- b. 86 and 85
19. A capacitor can be used in what components?
- d. All of the above
10. For an electrical device to operate, it must have ________________.
- a. power and a ground
11. A capacitor _______________.
- a. stores electrons
- b. passes AC
- c. blocks DC
- d. all of the above
27. Electromagnetic interference can be reduced by using a _____________.
- d. any of the above
26. An ignition coil operates using the principle(s) of __________________.
- d. all of the above X
29. Magnetic field strength is measured in _________ .
- a. ampere-turns
Which terminal of the OBD-II data link connector is the signal ground for all vehicles?
- 5

Question 1 studiers recently

Which of the following is true about nodes?

Answer

Aceify Homework Helper

Students also studied these questions

A capacitor used for spike protection will normally be placed in _______ to the load or circuit.

A capacitor used for spike protection will normally be placed in _______ to the load or circuit.

What will be the total capacitance value in a circuit with capacitors connected in parallel?

In a condenser microphone, the _________ is the negatively charged plate of a charged capacitor.

Identify the insulating material used between two conductive plates in a capacitor.

How many charges of electrons is equal to one coulomb?

A charged capacitor acts like a ________.

To increase the capacity, what could be done?

Capacitors block the flow of ______ current but allow _____current to pass.

The unit of measurement for capacitor rating is called the _______.

A capacitor _______________.

What happens to the electrostatic attraction in a condenser microphone if the distance between the plates is reduced?

Capacitors are often used as “suppression capacitors.” What does a capacitor suppress?

Two technicians are discussing the operation of a capacitor. Technician A says that a capacitor can create electricity. Technician B says that a capacitor can store electricity. Which technician is correct?

Which of the following statements is true with respect to a Leyden jar?

The relative strength of a material against the flow of electrical current is called __________.

___________ of the coil is rapidly released when voltage spike is reduced in a capacitor in parallel connection.

__________ are often combined with capacitors to act as electromagnetic interference (EMI) filter circuits for windshield wiper and electric fuel pump motors.

Which of the following is used to reduce radio interference or to improve the performance of a high-power sound system.

Capacitance can be increased by which one of the following factors?

The relative strength of a material against the flow of electrical current is called __________.

Magnetic field strength is measured based on _________.

11. Which type of loops are formed by the magnetic field lines?

Which of the following rules is used to determine the direction of the magnetic force or thrust on a wire carrying current in a magnetic field?

12. When a conductor cuts across magnetic flux lines, the amount of the voltage depends on _____________.

Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?

The EMF induced in a coil due to the change of flux linked with its own turns is called __________.

Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?

The conventional theory for current flow is being used to determine the direction of magnetic lines of force. Technician A says that the left-hand rule should be used. Technician B says that the right-hand rule should be used. Which technician is correct?

An ignition coil is an example of a _______________.

When a conductor is moved to cut magnetic flux lines at an angle of 90 degrees, __________.

An ignition coil operates using the principle(s) of __________________.

Unlike magnetic poles ____________ and like magnetic poles _______________.

Technician A says that a relay is an electromagnetic switch. Technician B says that a solenoid uses a movable core. Which technician is correct?

The phenomenon due to which there is an induced current in one coil due to the current in a neighboring coil is called _______________.

All electronic devices used in vehicles are affected by _________.

16. As the magnetic flux density increases, the reluctance ________.

The point in a magnet where the intensity of magnetic lines of force is maximum is called ________.

A solenoid is an example of which type of switch?

The right-hand rule shows the direction of ____________.

Unlike magnetic poles ____________ and like magnetic poles _______________.

1. On a wiring diagram, S110 with a "0.8 BRN/BLK" means ______.

12. Capacitors are often used as “suppression capacitors”. What does a capacitor suppress?

17. Capacitors block the flow of ______ current but allow _____current to pass.

16. Two technicians are discussing the operation of a capacitor. Technician A says that a capacitor can create electricity. Technician B says that a capacitor can store electricity. Which technician is correct?

15. The unit of measurement for capacitor rating in called the _______.

18. To increase the capacity what could be done?

20. A capacitor used for spike protection will normally be placed in _______ to the load or circuit.

22. Unlike magnetic poles ____________ and like magnetic poles _______________.

28. An ignition coil is an example of a _______________.

21. Technician A says that magnetic lines of force can be seen by placing iron filings on a piece of paper and holding them over a magnet. Technician B says that the effects of magnetic lines of force can be seen using a compass. Which technician is correct?

23. The conventional theory for current flow is being used to determine the direction of magnetic lines of force. Technician A says that the left-hand rule should be used. Technician B says that the right-hand rule should be used. Which technician is correct?

24. Technician A says that a relay is an electromagnetic switch. Technician B says that a solenoid uses a movable core. Which technician is correct?

2. Where is connector C250?

9. A short circuit can be located using a ____________.

3. All switches illustrated in schematics are ______________.

13. Capacitors are commonly used as a___________.

14. A charged capacitor acts like a ________.

6. Which relay terminal is the normally closed (N.C.) terminal?

5. Technician A says that a good relay should measure between 60 and 100 ohms across the coil terminals. Technician B says that OL should be displayed on an ohmmeter when touching terminals 30 and 87. Which technician is correct?

2. Where is connector C250?

7. Technician A says that there is often more than one circuit being protected by each fuse. Technician B says that more than one circuit often shares a single ground connector. Which technician is correct?

4. When testing a relay using an ohmmeter, which two terminals should be touched to measure the coil resistance?

19. A capacitor can be used in what components?

10. For an electrical device to operate, it must have ________________.

11. A capacitor _______________.

27. Electromagnetic interference can be reduced by using a _____________.

26. An ignition coil operates using the principle(s) of __________________.

29. Magnetic field strength is measured in _________ .

Which terminal of the OBD-II data link connector is the signal ground for all vehicles?

Similar questions

Technician A says that module communications networks are used to reduce the number of wires in a vehicle. Technician B says that a communications network is used to share data from sensors, which can be used by many different modules. Which technician is correct?

11. Technician A says that module communications networks are used to reduce the number of wires in a vehicle. Technician B says that a communications network is used to share data from sensors, which can be used by many different modules. Which technician is correct?

All of the following statements are true of electrical systems that use networks, EXCEPT:

Three of the four power windows in a vehicle operate normally. What is the most likely cause?

Question
1 studiers recently

Capacitors block the flow of __ current but allow _current to pass.

Unlike magnetic poles and like magnetic poles ___.

Unlike magnetic poles and like magnetic poles ___.

17. Capacitors block the flow of __ current but allow _current to pass.

22. Unlike magnetic poles and like magnetic poles ___.